In **Electric current** the *electric* refers to *electricity* and the *current* refers to flow of electrical charge.

## ExamplesEdit

Lightning is an example of an electric current, as is the solar wind, the source of the polar aurora. Probably the most familiar form of electric current is the flow of conduction electrons in a metallic wire. This is how utility companies deliver electricity. In electronics, electric current is most often the flow of electrons through conductors and devices such as resistors, but it is also the flow of ions inside a battery or the flow of holes within a semiconductor.

## Relation between current and charge Edit

The symbol typically used for the amount of current (the amount of charge *Q* flowing per unit of time *t*) is * I*, from the German word

*Intensität*, which means 'intensity'.

- $ I = {dQ \over dt} $

Formally this is written as

- $ i(t) = {dq(t) \over dt} $ or inversely as $ q(t) = \int_{-\infty}^{t} i(x)\, dx $

## Conventional current Edit

**Conventional current** was defined early in the history of electrical science as a flow of positive charge. In solid metals, like wires, the positive charges are immobile, and only the negatively charged electrons flow in the direction opposite conventional current, but this is not the case in most non-metallic conductors. In other materials, charged particles flow in both directions at the same time. Electric currents in electrolytes are flows of electrically charged atoms (ions), which exist in both positive and negative varieties. For example, an electrochemical cell may be constructed with salt water (a solution of sodium chloride) on one side of a membrane and pure water on the other. The membrane lets the positive sodium ions pass, but not the negative chlorine ions, so a net current results. Electric currents in plasma are flows of electrons as well as positive and negative ions. In ice and in certain solid electrolytes, flowing protons constitute the electric current. To simplify this situation, the original definition of conventional current still stands.

There are also instances where the electrons are the charge that is physically moving, but where it makes more sense to think of the current as the movement of positive "holes" (the spots that should have an electron to make the conductor neutral). This is the case in a p-type semiconductor.

The SI unit of electrical current is the ampere. Electric current is therefore sometimes informally referred to as * amperage* or

*, by analogy with the term*

**ampage***voltage*. Though this is a valid term, some engineers frown on it.

## The speed of an electric currentEdit

The mobile charged particles within a conductor move constantly in random directions. In order for a net flow of charge to exist, the particles must also move together with an average drift rate. For example, during currents in metals the particles follow an erratic path, bouncing from atom to atom, but generally drifting in the direction of the electric field. The speed at which they drift can be calculated from the equation:

- $ I=nAvQ \!\ $

where

*I*is the current*n*is number of charged particles**per unit volume***A*is the cross-sectional area of the conductor*v*is the drift velocity, and*Q*is the charge on each particle.

Electric currents in solid matter are typically very slow flows. For example, in a copper wire of cross-section 0.5 mm², carrying a current of 5 A, the *drift velocity* of the electrons is of the order of a millimetre per second. To take a different example, in the near-vacuum inside a cathode ray tube, the electrons travel in near-straight lines ("ballistically") at about a tenth of the speed of light.

However, we know that electric current signals are waves which propagate at very high speed. As with any wave, the speed of the waves in a medium have little relation to the speed of that medium as it moves. For example, in AC power lines, the waves of current propagate rapidly from a source to a distant load, while the charges themselves only move back and forth over a tiny distance. The velocity of flowing charges can be quite low, while any changes in electric current can travel at the speed of light, which might be slower in a particular medium. The percentage of speed in a medium compared to the speed of light in vacuum is called velocity factor, and is proportional to refractive index.

## Current density Edit

**Current density** is the current per unit (cross-sectional) area.

Mathematically, current is defined as the net flux through an area. Thus:

- $ I = j \cdot A $

where, in the MKS or SI system of measurement,

*I*is the current, measured in amperes*j*is the "current density" measured in amperes per square metre*A*is the area through which the current is flowing, measured in square metres

The current density is defined as:

- $ j=\int_i n_i \cdot x_i \cdot \mathbf{u_i} $

where

*n*is the particle density (number of particles per unit volume)*x*is the mass, charge, or any other characteristic whose flow one would like to measure.*u*is the average velocity of the particles in each volume

Current density is an important consideration in the design of electrical and electronic systems. Most electrical conductors have a finite, positive resistance, making them dissipate power in the form of heat. The current density must be kept sufficiently low to prevent the conductor from melting or burning up, or the insulating material failing. In superconductors, excessive current density may generate a strong enough magnetic field to cause spontaneous loss of the superconductive property.

## Electromagnetism Edit

Every electric current produces a magnetic field. The magnetic field can be visualized as a pattern of circular field lines surrounding the wire.

Electric current can be directly measured with a galvanometer, but this method involves breaking the circuit, which is sometimes inconvenient. Current can also be measured without breaking the circuit by detecting the magnetic field it creates. Devices used for this include Hall effect sensors, current clamps and Rogowski coils.

## Ohm's law Edit

Ohm's law predicts the current in an (ideal) resistor (or other ohmic device) to be the quotient of applied voltage over electrical resistance:

- $ I = \frac{V}{R} $

where

*I*is the current, measured in amperes*V*is the potential difference measured in volts*R*is the resistance measured in ohms

## Electrical safety Edit

The most obvious hazard is electric shock, where a current through part of the body can cause effects from a slight tingle to cardiac arrest or severe burns. It is the current that passes that determines the effect, and this depends on the nature of the contact, the condition of the body part, the current path through the body and the voltage of the source. The effect also varies considerably from individual to individual. (For approximate figures see **Shock Effects** under Electric shock.) Because of this and because in practical situations the current that may pass cannot be predicted any supply of over 24 volts should be considered a possible source of dangerous electric shock. In particular note that 110 volts can certainly be lethal.

Electric arcs, which can occur with supplies well below 24 volts, are very hot and emit ultra-violet and infra-red radiation. Proximity to an electric arc can therefore cause severe burns while UV is damaging to the unprotected eye.

Accidental electric heating can also be dangerous. An overloaded power cable is a frequent cause of fire. A battery as small as an AA cell placed in a pocket with change can lead to a short circuit heating the battery and the coins which may inflict burns. NiCad and NiMh cells are particularly risky because they can deliver a very high current due to their low internal resistance.

## See alsoEdit

- Alternating current
- Direct current
- electrical conduction for more information on the physical mechanism of current flow in materials
- SI electromagnetism units

## External linksEdit

- Online Current Converter - convert between various units of current, such as
*ampere*,*biot*,*abampere*,*statampere*, and so on - Online Electricity Surface Current Density Calculator - Online Electricity surface current density converter, converts value of specified unit to various units.

- Interactive Current Conversion Table - convert selected unit to all other units of current

This page uses Creative Commons Licensed content from Wikipedia (view authors). |